Genset synchronizer rental
Genset synchronizer rental | Daytime savings have a way to make people out of sync, especially if they forget to change their hours. Just as people need to synchronize their hours to the correct time, generators must be synchronized if they are removed from service and reconnected to the power system during load variations, emergency outages, maintenance, and in other situations. This useful article is made for Arthur Teknik to explain what you need to know about Genset synchronization.
Phone 1 : +6281316854183 (Jakarta)
Phone 2 : +628111836468 (Jakarta)
Phone 3 : +6281210463637 (Jakarta)
Phone 4 : +62818960565 (Bali)
Email : marketing@arthurteknik.com
Genset synchronization is the process of matching parameters such as voltage, frequency, phase angle, phase sequence, and alternator (generator) waveforms or other sources with a healthy or running power system. This is done before the generator is connected back to the power system. After the generator is synchronized with other generators, alternator or bar bus parameters, the system can run smoothly again.
Why is the synchronization of the generator needed? Because the generator cannot send power to the power system unless all the parameters mentioned above are the same as those on the network. The need for synchronization occurs when two or more alternators work together to supply power to the load. Because the electric charge is not constant, two or more generators that supply power must be interconnected and operate in parallel to handle larger loads.
The conditions for operating a Genset in parallel or synchronous "Synchronizing Generator" are as follows:
1. The working voltage (Voltage) of each generator.
2. The sequence of a phase of each generator (Phase Direction).
3. Frequency (Hertz) Each generator.t.
4. Phase angles of each generator.
Because two generators are driven by two different drivers, the speed (RPM) of each drive generator must be different. This difference can cause a slight difference in the phase angle, the difference in phase angle will cause differences in the power factor up and down.
Power factors can affect generator operation in parallel, generators that have smaller power factors will bear higher power loads while generators that have higher power factors will bear lower loads. If the difference in power factor is still in the normal range, this is not too much of a problem, but if the difference in power borne by one generator exceeds the maximum power of the generator, the generator will not be able to bear the burden.
So ideally the generator to be parallelized must have the same voltage or power factor. In generators to be parallelized, equipment is usually called a Droop kit. This droop kit is in the form of a current transformer that is installed in the Output generator section of the coil and is connected to an automatic voltage regulator (AVR). This Droop kit serves to regulate the power factor based on the amount of current loaded on the generator so that the load sharing for each generator can be adjusted.
The following are the advantages of generator synchronization
1. Get more power.
2. Operational cost efficiency.
3. To ensure continuity of the availability of electric power.
Thus the discussion about what is a Genset synchronizer. For those of you who need a Genset synchronizer, you can rent it at Arthur Teknik. Arthur Teknik is the vendor of generator rental, misty fan rental services, the best ac rental and electricity rental services in Indonesia, with the handling of major events in Indonesia, such as Asian para games and also supported by a reliable team to make Arthur Engineering the solution for you who want or need a generator rental service. To consult Arthur Technique you can contact the number below:
Why is the synchronization of the generator needed? Because the generator cannot send power to the power system unless all the parameters mentioned above are the same as those on the network. The need for synchronization occurs when two or more alternators work together to supply power to the load. Because the electric charge is not constant, two or more generators that supply power must be interconnected and operate in parallel to handle larger loads.
The conditions for operating a Genset in parallel or synchronous "Synchronizing Generator" are as follows:
1. The working voltage (Voltage) of each generator.
2. The sequence of a phase of each generator (Phase Direction).
3. Frequency (Hertz) Each generator.t.
4. Phase angles of each generator.
Because two generators are driven by two different drivers, the speed (RPM) of each drive generator must be different. This difference can cause a slight difference in the phase angle, the difference in phase angle will cause differences in the power factor up and down.
Power factors can affect generator operation in parallel, generators that have smaller power factors will bear higher power loads while generators that have higher power factors will bear lower loads. If the difference in power factor is still in the normal range, this is not too much of a problem, but if the difference in power borne by one generator exceeds the maximum power of the generator, the generator will not be able to bear the burden.
So ideally the generator to be parallelized must have the same voltage or power factor. In generators to be parallelized, equipment is usually called a Droop kit. This droop kit is in the form of a current transformer that is installed in the Output generator section of the coil and is connected to an automatic voltage regulator (AVR). This Droop kit serves to regulate the power factor based on the amount of current loaded on the generator so that the load sharing for each generator can be adjusted.
The following are the advantages of generator synchronization
1. Get more power.
2. Operational cost efficiency.
3. To ensure continuity of the availability of electric power.
Thus the discussion about what is a Genset synchronizer. For those of you who need a Genset synchronizer, you can rent it at Arthur Teknik. Arthur Teknik is the vendor of generator rental, misty fan rental services, the best ac rental and electricity rental services in Indonesia, with the handling of major events in Indonesia, such as Asian para games and also supported by a reliable team to make Arthur Engineering the solution for you who want or need a generator rental service. To consult Arthur Technique you can contact the number below:
Phone 1 : +6281316854183 (Jakarta)
Phone 2 : +628111836468 (Jakarta)
Phone 3 : +6281210463637 (Jakarta)
Phone 4 : +62818960565 (Bali)
Email : marketing@arthurteknik.com
Komentar
Posting Komentar